View MLX90308LUF_4141769.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MLX90308
Programmable Sensor Interface
Features and Benefits
s s s s s s
Microprocessor-controlled signal conditioning for bridge-type sensors Suited for low-cost sensors: reduction of non-linearity by programmable coefficients External or internal temperature sensor for compensating temperature errors Versatile output signal ranges: 4, 5, 10, or 11VDC; 4 to 20 mA loop Mass calibration easy with 2400 or 9600 baud UART Power supply from 6 to 35VDC
Applications
Pressure transducers Accelerometers Temperature sensor assemblies Linear position sensors
s s s
Ordering Information
Part No. MLX90308 MLX90308 Temperature Suffix L (-40C to +150C) L (-40C to +150C) Package code DF (SOIC16w) UF (die on foil)
Description
The MLX90308 is a dedicated microcontroller which performs signal conditioning for sensors wired in bridge or differential configurations. Sensors that can be used include thermistors, strain gauges, load cells, pressure sensors, accelerometers, etc. The signal conditioning includes gain adjustment, offset control, high order temperature and linearity compensation. Compensation values are stored in EEPROM and are reprogrammable. Programming is accomplished by using a PC, with an interface circuit (level shifting and glue logic), and provided software. The application circuits can provide an output of an absolute voltage, relative voltage, or current. The output can be range limited with defined outputs when the signal is beyond the programmed limits. Other features include alarm outputs and level steering. The robust electrical design allows the MLX90308 to be used where most signal conditioning and sensor interface circuits cannot be used. Voltage regulation control is provided for absolute voltage and current modes (external FET required). The standard package is a plastic SO16W. The device is static-sensitive and requires ESD precautions.
MLX902xx Name of Sensor Rev Y.X 22/Aug/98 3901090308
Page 1Page 1
Apr/04
Rev 006
MLX90308
Programmable Sensor Interface
3901090308 Rev 006
Page 2
Apr/04
Figure 1. Functional Block Diagram
MLX90308
Programmable Sensor Interface
Table 1. MLX90308 Electrical Specifications
Parameter
Regulator & Consumption Input voltage range Supply current Supply current Regulated supply voltage Regulated voltage temperature coefficient Supply rejection ratio Instrumentation Amplifier Differential input range Differential input range Common mode input range Pin leakage current Common mode rejection Ratio CMRR Hardware gain Coarse offset control Range CSOF[1:0] = 00 CSOF[1:0] = 01 CSOF[1:0] = 10 CSOF[1:0] = 11 Fixed offset control range High Low IA chopper frequency Gain Stage Course gain (Fixed Gain = 1023) CSGN = 000 CSGN = 001 CSGN = 010 * CSGN = 100 to 111: voltage mode only, not applicable to current mode. Output > 6.5V; MSB = 1 Output < 6.5V; MSB = 0 CSGN = 011 CSGN = 100* CSGN = 101*
Page 3Page 3
DC operating parameters: TA = -40 to 140oC, VDD1 = 6 to 35VDC (unless otherwise specified).
Symbol
Test Conditions
Min
Typ
Max
Units
VIN IDD IDD VREG
VDD1 (Regulator connected) @ TA = 100C Current Mode @ TA = 100C Voltage Mode
6 2.1
35
V mA
5.0 4.5 4.75 -600 5.2
mA V uV / C dB
PSRR
VDD1 > 6V
90
VBP-VBN VBP-VBN
IINV = 0 IINV = 1 1/2(VBP+VBN) Pins VBP & VBN to GND, VDD =
-11.0 -32.0 38.0
32.0 11.0 65.0 8.0
mV/V(Vdd) mV/V(Vdd) %VDD nA dB
60 18 -15.3 -5.1 3.8 13.9 6.0 -7.0 300 22 -13.9 -3.8 5.1 15.3 8.0 -5.0
V/V mV/V mV/V mV/V mV/V mV/V mV/V kHz
3.0 4.9 8.0 12.8 7.9 12.7
3.3 5.4 8.8 14.1 8.7 14.0
V/V V/V V/V V/V V/V V/V
Apr/04
MLX902xx Name of Sensor Rev Y.X 22/Aug/98 3901090308
Rev 006
MLX90308
Programmable Sensor Interface
Table 1. MLX90308 Electrical Specifications (continued)
Parameter
Coarse gain Fixed gain control range Digital Mode & Current Mode Coarse Gain Stage Course Gain CSGN = 00 CSGN = 01 CSGN = 10 CSGN = 11 1.05 1.71 2.77 4.48 4.5 2.74 6.5 7.24 2.0 @ 0V output voltage Over complete output range CSGN[2:2] = 0 CSGN[2:2] = 1 Digital mode step size Capacitive load VMO pin Current Mode Output Stage Fixed gain Output current CMO pin Current sense resistor Digital mode current output span Digital mode current step Size Signal Path ( General) Overall gain Overall non-linearity Ratiometry Error (4.75V - 5.25V) Overall Gain < 250V/V Overall Gain > 250V/V
3901090308 Rev 006 Page 4
DC operating parameters: TA = -40 to 140oC, VDD1 = 6 to 35VDC (unless otherwise specified).
Test Conditions
CSGN = 110* CSGN = 111*
Min
20.4 33.1 0.480
Typ
Max
23.0 36.6 0.970 1.17 1.89 3.06 4.95 6.5 3.04 11 7.86 -0.2
Units
V/V V/V V/V V/V V/V V/V V/V V V/V V V/V V mA uA
Voltage Mode Output Stage ( See Voltage Mode)
Output voltage span CSGN[2:2] = 0 Gain CSGN[2:2] = 1 Gain Minimum output voltage Output source current Output sink current Output resistance Digital mode output span 20 25 6.5 11.0 6.5 11.0 10 RSENSE = 24 ohm Current mode VDD = 5V VDD = 5V,RSENSE=24 Voltage mode Current mode = 24 28 81 -0.25 -0.5 -1.3 23 30 600 750 0.25 0.5 +1.3 8.4 27 24 9.3
Ohms V V mV mV nF mA/V mA Ohms mA uA V/V mA/V % % %
Apr/04
VDD = 5V, CSGN[2:2]=0 VDD = 5V, CSGN[2:2]=1
MLX90308
Programmable Sensor Interface
Table 1. MLX90308 Electrical Specifications (continued)
Parameter
Bandwidth (-3dB)
DC operating parameters: TA = -40 to 140oC, VDD1 = 6 to 35VDC (unless otherwise specified).
Test Conditions
39 nF connected from FLT to GND
Min
2.8
Typ
3.5
Max
4.2 7.1
Units
KHz mVRMS
Noise, VDD = 5V, CFLT=39nF, CL=10nF, RL =5K , Analog Mode Temperature Sensor & - Amplifier Temperature sensor sensitivity Temperature sensor output voltage Temperature Sensor & Amplifier (continued). Input voltage range TMP pin @ VDD = 5.0V GNTP[1,0] = 00 GNTP[1,0] = 01 GNTP[1,0] = 10 GNTP[1,0] = 11 DAC Resolution Monotonicity Ratiometric output range (DAC output) Offset Error Differential non-linearly Integral non-linearity ADC Resolution Monotonicity Ratiometric input range Offset error Differential non-linearly Integral non-linearity On-Chip RC Oscillator and Clock Untrimmed RC oscillator frequency Trimmed RC oscillator frequency (Measured at TMP pin with TSTB pin pulled low after power up) Frequency temperature coefficiency Clock Stability with temperature compensation over full temperature range Ratio of f (microcontroller main clock and (RC oscillator) TURBO = 0 TURBO = 1
Page 5Page 5
390 70 380
uV/C mV
207 145 101 71
517 367 263 186
mV mV mV mV
10 Guaranteed By Design 1 10 1 2 75
Bit
% VDD LSB LSB LSB
10 Guaranteed by design 1 10 1 2 75
Bit
% VDD LSB LSB LSB
40 86.9 87.8 26 -3 7 28
250 88.7
kHz kHz Hz/C
+3
%
MLX902xx Name of Sensor Rev Y.X 22/Aug/98 3901090308
Apr/04
Rev 006
MLX90308
Programmable Sensor Interface
Table 1. MLX90308 Electrical Specifications (continued)
Parameter
Input & Output Pins (I01 & I02) Digital input levels Output Levels TSTB Pin Input levels Low High Pull-up Resistor FLT Pin Output resistance Output voltage range OFC Pin Output voltage range Load capacitor UART & COMS Pin UART baud rate TURBO = 0 TURBO = 1 COMS pin input levels Low High COMS Pin Output Resistance Low High 100 100 0.3*VDD 2400 9600 baud baud V 0.7*VDD V Ohms kOhms VDD = 5V 0.05 3.75 20 V pf VDD = 5V 0.05 1.24 3.6 kOhms V 66 0.5 VDD-0.5 kOhms V Low High @ output current = 5mA low @ Output current = 5mA high 0.5 VDD-0.5 VDD-0.4 VDD 0.4 V V
DC operating parameters: TA = -40 to 140oC, VDD1 = 6 to 35VDC (unless otherwise specified).
Test Conditions
Min
Typ
Max
Units
3901090308 Rev 006
Page 6
Apr/04
MLX90308
Programmable Sensor Interface
Unique Features
Customization
Melexis can customize the MLX90308 in both hardware and firmware for unique requirements. The hardware design provides 64 bytes of RAM, 3 kbytes of ROM, and 48 bytes of EEPROM for use by the firmware.
Table 2. Absolute Maximum Ratings
Supply voltage (ratiometric) VDD Max Supply voltage (ratiometric) VDD Min
6V 4.5V 35V -0.7V 3.5mA 4.5mA 8mA 100mA 8mA +11V 71mW
-40 to +140 -55 to +150
Supply voltage (operating), VDD1 Max Reverse voltage protection Supply current, Current Mode, IDD Supply current, Voltage Mode, IDD Output current, IVMO Output current (short to VDD), ISCVMO Output current (short to VSS), ISCVMO Output voltage, VVMO Power dissipation, PD Operating temperature range, TA Storage temperature range, TS Maximum junction temperature, TJ
Special Information
The output of the sensor bridge is amplified via offset and gain amplifiers and then converted to the correct output signal form in one of the output stages. The sensitivity and offset of the analog signal chain are defined by numbers passed to the DAC interfaces from the microcontroller core (GN[9:0] and OF[9:0]). The wide range of bridge offset and gain is accommodated by means of a 2-bit coarse adjustment DAC in the offset adjustment (CSOF[1:0]), and a similar one in the gain adjustment (CSGN[2:0]). The signal path can be directed through the processor for digital processing. Two I/O pins are available for analog inputs or digital outputs. These pins can be used for alarms on various points on the analog signal path and built-in or external temperature values.
150C
Programming and Setup
The MLX90308 needs to have the compensation coefficients programmed for a particular bridge sensor to create the sensor system. Programming the EEPROM involves some minimal communications interface circuitry, Melexis' setup software, and a PC. The communications interface circuitry is available in a development board. This circuitry communicates with the PC via a standard RS232 serial communications port.
Cross Reference
There are no known devices which the MLX 90308 can replace.
ESD Precautions
Observe standard ESD control procedures for CMOS semiconductors.
MLX902xx Name of Sensor Rev Y.X 22/Aug/98 3901090308
Page 7Page 7
Apr/04
Rev 006
MLX90308
Programmable Sensor Interface
Table 3. Pin Description
Pin 1,2 Signal Name I/O1, 2 Description Bi-directional I/O. Can also be used as input to A/D converter. I/O can be controlled by serial communications or by firmware as alarm inputs or level out. (unconnected when not used) Test pin for Melexis production testing. (in normal application connected to VDD) Filter pin; allows for connection of a capacitor to the internal analog path. Offset control output. Provides access to the internal programmed offset control voltage for use with external circuitry. (unconnected when not used) Bridge inputs, negative and positive. Temperature sensor input. An external temperature sensor can be used in conjunction with the internal one. The external sensor can provide a temperature reading at the location of the bridge sensor. Regulated supply voltage. Used for internal analog circuitry to ensure accurate and stable signal manipulation. Regulator FET gate control. For generating a stable supply for the bridge sensor and internal analog circuitry (generates regulated voltage for VDD). Unregulated supply voltage. Used for digital circuitry and to generate FET output. Voltage mode output. Compensated sensor output voltage. Current mode output. Compensated sensor output for current mode operation. Current mode negative rail. Current mode return path. Power supply return. Serial communications pin. Bi-directional serial communication signal for reading and writing to the EEPROM.
3 4 5 6,7 8
TSTB FLT OFC VBN,VBP TMP
9 10 11 12 13 14 15 16
VDD FET VDD1 VMO CMO CMN GND COMS
1
IO1 IO2
COMS
16
2
GND
15
3
TSTB
CMN
14
4
FLT
CMO
13
5
OFC
VMO
12
6
VBN
VDD1
11
7
VBP
FET
10
8
TMP
VDD
9
Figure 2. Pinout (SO16W (LW) Package)
3901090308 Rev 006 Page 8 Apr/04
MLX90308
Programmable Sensor Interface
Analog Features
Supply Regulator
Power-On Reset
The Power-On Reset (POR) initializes the state of the digital part after power up. The reset circuitry is completely internal. The chip is completely reset and A bandgap-stabilized supply-regulator is on-chip while fully operational 3.5 ms from the time the supply crosses the pass-transistor is external. The bridge-type sensor 3.5 volts. The POR circuitry will issue another POR if is typically powered by the regulated supply (typically the supply voltage goes below this threshold for 1.0 us. 4.75V). For ratiometric operation, the supply-regulator can be disabled by connecting together the Test Mode unregulated and regulated supply pins. For 100% testability, a "TEST" pin is provided. If the pin is pulled low, then the monitor program is entered and Oscillator the chip changes its functionality. In all other The MLX90308 contains a programmable on-chip RC applications, this pin should be pulled high or left oscillator. No external components are needed to set floating (internal pull-up). the frequency (87.8 kHz +/-1%). The MCU-clock is generated by a PLL (phase locked loop tuned for 614 Temperature Sense kHz or 2.46 Mhz) which locks on the basic oscillator. The temperature measurement, TPO, is generated from The frequency of the internal clock is stabilized over the external or internal temperature sensor. This is the full temperature range, which is divided into three converted to a 10-bit number for use in calculating the regions, each region having a separate digital clock signal compensation factors. A 2-bit coarse adjustment setting. All of the clock frequency programming is GNTP[1:0] is used for the temperature signal gain & done by Melexis during final test of the component. offset adjustment. The device uses the internal temperature sensor to determine which temperature range setting to use.
A/D and D/A Conversions using only one DAC
For saving chip area, the "Offset DAC" is multiplexed in various ways. Both "fine offset" and "digital mode" signals are stored on a capacitor. An ADC-loop is available by using a comparator and SAR.
D/A
Before changing to another capacitor, the DAC output should be settled to the new value. For example, MODSEL moves the analog multiplexer to the socalled "open state 0." At the same time, the 10 bit mux selects OF[9:0] for the offset-DAC. After the DAC settling time, the analog multiplexer is moved to its final state and the DAC-output is stored on a capacitor.
A/D
The S/W-Signal MODSEL connects the SAR-output to the DAC and the DAC-output to the comparator. The SARegister is initialized by a rising edge of STC (S/W signal). At the end of the A/D conversion, the EOC flag is set to 1 and the controller can read the ADC values.
MLX902xx Name of Sensor Rev Y.X 22/Aug/98 3901090308
Page 9Page 9
Apr/04
Rev 006
MLX90308
Programmable Sensor Interface
Digital Features
Microprocessor, LX11 Core, Interrupt Controller, Memories
The LX11 microcontroller core is described in its own datasheet. As an overview, this implementation of the LX11 RISC core has following resources: Two accumulators, one index and two interrupt accumulators. 15 - 8 bit I/O ports to internal resources. 64 byte RAM. 4 kbytes ROM : 3 kbytes is available for the customer's application firmware. 1k is reserved for test. 48 x 8 bit EEPROM. Four interrupt sources, two UART interrupts and two timers.
Timer
The clock of the timers TMI and TPI is taken directly from the main oscillator. The timers are never reloaded, so the next interrupt will take place 2x oscillator pulses after the first interrupt.
Watch Dog
An internal watch dog will reset the whole circuit in case of a software crash. If the watch dog counter is not reset at least once every 26 milliseconds (@ 2.46 MHz main clock), the microcontroller and all the peripherals will be reset.
Firmware
The MLX90308 firmware performs the signal conditioning by either of two means: analog or digital. The analog signal conditioning allows separate offset and gain temperature coefficients for up to four temperature ranges. Digital mode allows for all of the analog capabilities plus up to five different gain values based on the input signal level. Also available in both modes is the capability of range limiting and level steering. .
UART
The serial link is a potentially full-duplex UART. It is receive-buffered, in that it can receive a second byte before a previously received byte has been read from the receiving register. However, if the first byte is not read by the time the reception of the second byte is completed, the first byte will be lost. The UART's baud rate depends on the RC-oscillator's frequency and the "TURBO"-bit (see output port). Transmitted and received data has the following structure: start bit = 0, 8 bits of data, stop bit = 1.
Temperature Processing
In both analog and digital modes, the temperature reading controls the temperature compensation. This temperature reading is filtered as designated by the user. The filter adjusts the temperature reading by factoring in a portion of the previous value. This helps to minimize the effect of noise when using an external temperature sensor. The filter equation is: If measured_temp > Temp_f(n) then Temp_f(n+1) = Temp_f(n) + [measured_temp Temp_f(n)] / [2 n_factor]. If measured_temp < Temp_f(n), then Temp_f(n+1) = Temp_f(n) - [measured_temp Temp_f(n)] [2 n_factor]. Temp_f(n+1) = new filtered temperature value. Temp_f(n) = previous filtered temperature value. Measured_temp = Value from temperature A to D.
Sending Data
Writing a byte to port 1 automatically starts a transmission sequence. The TX Interrupt is set when the STOP-bit of the byte is latched on the serial line.
Receiving Data
Reception is initialized by a 1 to 0 transition on the serial line (i.e., a START-bit). The baud rate period (i.e., the duration of one bit) is divided into 16 phases. The first six and last seven phases of a bit are not used. The decision on the bit-value is then the result of a majority vote of phase 7, 8 and 9 (i.e., the center of the bit). Spike synchronization is avoided by de-bouncing on the incoming data and a verification of the START-bit value. The RX Interrupt is set when the stop bit is latched in the UART.
N_factor = Filter value set by the user (four LSB's of byte 25 of EEPROM), range 0-6. The filtered temperature value, Temp_f, is stored in RAM bytes 58 and 59. The data is a 10 bit value, left justified in a 16 bit field.
3901090308 Rev 006
Page 10
Apr/04
MLX90308
Programmable Sensor Interface
OFFSET
Different Modes
Analog Mode
The parameters OF and GN represent, respectively, offset correction and span control, while OFTCi and GNTCi represent their temperature coefficients (thermal zero shift and thermal span shift). After reset, the firmware continuously calculates the offset and gain DAC settings as follows: The EEPROM holds parameters GN, OF, OFTCi and GNTCi, where "i" is the gap number and can be 1 < i < 4. The transfer function is described below. Vout = FG * DAC_GAIN {Vin+DAC_OFFSET+CSOF} * CSGN[2:0] *
DAC_OFFSET (new value) ~ OF[9:0]+[OFTCi* dT] OF[9:0] = Fixed Gain, bytes 4 and 17 in EEPROM. OFTCi = Offset for a given temperature segment I. OFTCiL and OFTCiH in EEPROM table. dT = Temp. change within the appropriate gap. Calculation of the offset for a given temperature segment is performed the same way as for the gain.
(7 - -6) *
OF [9 : 0] - 6 = DAC _ OFFSET 1023
[mV/V]
Digital
Mode
The MLX90308 firmware provides the capability of digitally processing the sensor signal in addition to the analog processing. This capability allows for signal correction.
Iout = FG * DAC_GAIN * CSGN[1:0] * {Vin+DAC_OFFSET+CSOF} * 8.85mA/V FG = Hardware Gain (~20V/V). Part of the hardware design, and not changeable. CSGN = Course Gain, part of byte 2 in EEPROM. CSOF = Coarse Offset, part of byte 2 in EEPROM.
Signal Correction
While in digital mode the firmware can perform signal correction. This is an adjustment to the output level based on the input signal level. Adjustment coefficients can be set for five different signal ranges. The output is obtained by the following formula: 1st gap: Output = (Signal ) * PC1 + Poff Where: Signal = input signal measurement; Poff = Pressure ordinate = P1 PC1 = programmed coefficient first gap. Following gaps: Gap i: Output = (Signal - Pi) * PCi + Poff_i Where Signal = input signal measurement; Poff_i = Pressure ordinate (i = 2,3,4,5) Pi = Pressure signal point (i = 2,3,4,5) PCi = programmed coefficient first gap (i = 2,3,4,5). The PCi coefficients are coded on 12 bits: one bit for the sign, one for the unity, and the rest for the decimals. The Pi are coded on 10 bits (0-3FFh) in high-low order. PNB_TNB: contains the number of signal points, coded on the four MSB's. The four LSB's are reserved for the number of temperature points. See Table 4 and Table 5.
GAIN
DAC_GAIN (new value) ~ GN[9:0] + [GNTCi * dT] GN[9:0] = Fixed Gain, bytes 3 and 17 in EEPROM. GNTCi = Gain TC for a given temperature segment I. GNTCiL and GNTCiH in EEPROM table. dT = Temp. change within the appropriate gap. How to calculate gain in the first temp. gap?: DAC_GAIN = GN[9:0] - GNTC1 * (T1 - Temp_f1) How to calculate gain in the other temp. gaps?: 2nd gap: DAC_GAIN = GN[9:0] + GNTC2 * (Temp_f2 - T1) 3th gap: DAC_GAIN = DAC_GAIN2 + GNTC3 * (Temp_f3 - T2) 4th gap: DAC_GAIN = DAC_GAIN3 + GNTC4 * (Temp_f4 - T3) Where: Temp_f = Filtered temp. (previously described). If GNTC1 > 2047 => DAC_GAIN If GNTC2,3,4 > 2047 => DAC_GAIN [V/V]
(0.97 - 0.48) *
GN [9 : 0] + 0.48 = DAC _ GAIN 1023
Page 11 Page 11
MLX902xx Name of Sensor Rev Y.X 22/Aug/98 3901090308
Apr/04
Rev 006
MLX90308
Programmable Sensor Interface
Compensation Trade-Offs
A compromise must be made between temperature compensation and pressure correction. The EEPROM space where the signal coefficients are stored is shared with the temperature coefficients, with the result that an EEPROM byte can be used either for a temperature coefficient or for a signal coefficient, but not both. Table 6 presents the possibilities among the maximum number of temperature gaps and the maximum number of signal gaps.
Table 5. PNB_TNB Bit Definition; Temperature Gaps
# of Temperature Gaps Fixed (1) 2 Gaps 3 Gaps 4 Gaps 4 LSB of PNB_TNB 0 5 8 11 (B hex)
Table 4. PNB_TNB Bit Definition; Pressure Gaps
# of Pressure Gaps Fixed 1 2 3 4 5 4MSB of PNB_TNB Value 15 (F hex) 14 (E hex) 12 (C hex) 10 (A hex) 8 6
Table 6. Temperature & Signal Limitations
Maximum number of temperature gaps Fixed Gain and fixed Offset 2 Gaps 3 Gaps 4 Gaps Maximum number of signal gaps 5 Gaps 3 Gaps 2 Gaps Fixed signal
Figure 4. Signal Linearity Correction
Output
PC4
MLX90308
PC5
PC3
Output (units)
PC2
PC1
0
P2
P3
P4
P5
3901090308 Rev 006
Page 12
Apr/04
MLX90308
Programmable Sensor Interface
Alarm Option
This option allows controlling the low and high limits of the output (See Figure 5.). The output level is set when the output tries to exceed the programmed limits. Five bytes are reserved for this option. The first byte is the low trigger limit and the second the low output. The third and fourth bytes are used for the high limit and the output. The fifth byte is the alarm control, used to select the alarm input. The different levels are programmed as eight bit numbers. These correspond to the 8 upper bits of the 10 bit signal measurement. When the alarm mode is not used, all of the data is 0. The control code is coded as shown in Table 7. The six possible signals are listed below and are encoded on the 4 MSB's of byte 31 of the EEPROM.
IO1 & IO2
IO1 and IO2 are used in the alarm and level steering modes. For custom firmware, they can be used for a digital input, an analog input, or a digital output.
Figure 6. Alarm & Steering Source Points
OFC FLT VDD1 FET VDD GND Power Supply Regulation VBP
IAO
Offset Gain
GNO
VM
Table 7. Alarm Source Bit Definition
Selected input TPO IAO GNO VMO IO1 IO2 MUX Value 0010 0110 0000 0011 0100 0101
VMO
VBN
TPO
CM
CMO
CMN
TMP
Temp Sense & Amp ADC & DAC Microcontroller Core, Memory, EEPROM Reset,Test,& Oscillator
IO1 IO2
TSTB
Bidirectional I/O UART COMS
Figure 5. Alarm Function OUTPUT
MLX90308
Figure 7. Level Steering Function IO1, IO2
MLX90308
High Output
Output
1 -1
Parameter
1-0
Low Output
0-1
Low Trigger
High Trigger
0-0 (I02,I01)
Input Signal
Level 1
Level 2
Level 3
MLX902xx Name of Sensor Rev Y.X 22/Aug/98 3901090308
Page 13 Page 13
Apr/04
Rev 006
MLX90308
Programmable Sensor Interface
Level Steering
The level steering option allows configuration of the IO pins as outputs to indicate the relative level of a selected signal. See Figure 7. The levels at which the two outputs change state are programmed by the user. The programmed levels are set as eight bit numbers and compared to the upper eight bits of the digitized signal. This function utilizes the same resources as the alarm function. The two functions (level steering and alarm) can not be used simultaneously. Four bytes in the EEPROM command this option. The first byte is used to select the input, while the last three comprise the transition levels. The control byte for the level steering is the same as for the alarm. The four MSB's hold the code for the selected input. The control byte has several possibilities as designated by the MUX settings (See Table 8)
Communications
The MLX90308 firmware transfers a complete byte of data into and from the memory based on a simple command structure. The commands allow data to be read and written to and from the EEPROM and read from the RAM. RAM data that can be read includes the current digitized temperature and digitized GNO. The commands are described below. Melexis provides setup software for programming the MLX90308.
Table 8. Level Steering Bit Definitions
Selected input TPO IAO GNO VMO MUX Value 0010 0110 0000 0011
Table 9. Mode Byte Bit Definition
Bit 7 Function 1= EEPROM Checksum test active 0= EEPROM Checksum test inactive 0 = Analog Mode 1 = Digital Mode 0 = Alarm function inactive 1 = Alarm function active Remarks
EEPROM Checksum test. Checksum test failure will force the output to the value programmed in bytes 40 and 41 of the EEPROM (See Table 10). Digital mode must be activated when VMO and CMO both active. Alarm functions are like "limiting functions": If defined ADC INPUT is below low alarm trigger, then DIGMOD becomes active with alarm low output). If defined ADC INPUT is above high alarm trigger, then DIGMOD becomes active with alarm high output. Note: Deactivated if the level steering mode is active Depending on the sampled input, IO1/IO2 will be a two bit digital output. If IO1/IO2 are not active outputs, then they will be analog inputs.
6 5
4
0 = IO1/IO2 are not active outputs 1 = level steering: IO1/IO2 are active outputs 0 = Turbo inactive 1 = Turbo active 0 = VMO inactive 1 = VMO active 0 = Internal temperature sensor active 1 = External temperature sensor active 0 = CMO inactive 1 = CMO active
3 2 1
0
CMO has fixed digital value (EEPROM byte - see below) if both VMO and CMO are active. To activate this value, the digital mode must be activated.
Page 14 Apr/04
3901090308 Rev 006
MLX90308
Programmable Sensor Interface
Clock Temperature Stabilization UART Commands
The commands can be divided into three parts: (1) downloading of data from the ASIC, (2) uploading of data to the ASIC and (3) the reset command. All the commands have the same identification bits. The two MSB's of the sent byte indicate the command while the last six MSB's designate the desired address. The commands are coded as followed: 11 to read a RAM byte. 10 to read an EEPROM byte. 01 to write in the EEPROM. 00 to write in the RAM. The addresses can include 0-63 for the RAM, 0-47 for the EEPROM, and 63 for the EEPROM, RESET Command (read). To provide a stable clock frequency from the internal clock over the entire operating temperature range, three separate clock adjust values are used. Shifts in operating frequency over temperature do not effect the performance but do, however, cause the communications baud rate to change. The firmware monitors the internal temperature sensor to determine which of three temperature ranges the device currently is in. Each temperature range has a factory set clock adjust value, ClkTC1, ClkTC2, and ClkTC3. The temperature ranges are also factory set. The Ctemp1 and Ctemp2 values differentiate the three ranges. In order for the temperature A to D value to be scaled consistently with what was used during factory programming, the CLKgntp (temperature amplifier gain) valued is stored. The Cadj value stored in byte 1 of the EEPROM is used to control the internal clock frequency while the chip boots.
Downloading Command
With one byte, data can be downloaded from the ASIC. The ASIC will automatically send the value of the desired byte.
Unused Bytes
There are eight unused bytes in the EEPROM address map. These bytes can be used by the user to store information such as a serial number, assembly date code, production line, etc. Melexis doesn't guarantee that these bytes will be available to the user in future revisions of the firmware.
Uploading Command
Writing to the RAM or EEPROM involves a simple handshaking protocol in which each byte transmitted is acknowledged by the firmware. The first byte transmitted to the firmware includes both command and address. The firmware acknowledges receipt of the command and address byte by echoing the same information back to the transmitter. This "echo" also indicates that the firmware is ready to receive the byte of data to be stored in RAM or EEPROM. Next, the byte of value to be stored is transmitted and, if successfully received and stored by the firmware, is acknowledged by a "data received signal," which is two bytes of value BCh. If the "data received signal" is not observed, it may be assumed that no value has been stored in RAM or EEPROM.
EEPROM Checksum
A checksum test is used to ensure the contents of the EEPROM. The eight bit sum of all of the EEPROM addresses should have a remainder of 0FFh when the checksum test is enabled (mode byte). Byte 47 is used to make the sum remainder totals 0FFh. If the checksum test fails, the output will be driven to a user defined value, Faultval. When the checksum test is enabled, the checksum is verified at initialization of RAM after a reset.
Reset Command
Reading the address 63 of the EEPROM resets the ASIC and generates a received receipt indication. Immediately before reset, the ASIC sends a value of BCh to the UART, indicating that the reset has been received.
RAM Data
All the coefficients (pressure, temperature) are compacted in a manner similar to that used for the EEPROM. They are stored on 12 bits (instead of keeping 16 bits for each coefficient). All the measurements are stored on 16 bits. The user must have access to the RAM and the EEPROM, while interrupt reading of the serial port. Therefore, bytes must be kept available for the return address, the Aaccu and the B-accu, when an interrupt occurs. The RAM keeps the same structure in the both modes.
EEPROM Data
All user-settable variables are stored in the EEPROM within the MLX90308. The EEPROM is always reprogrammable. Changes to data in the EEPROM do not take effect until the device is reset via a soft reset or power cycle. 12 bit variables are stored on 1.5 bytes. The 4 MSB's are stored in a separate byte and shared with the four MSB's of another 12-bit variable.
MLX902xx Name of Sensor Rev Y.X 22/Aug/98 3901090308
Page 15 Page 15
Apr/04
Rev 006
MLX90308
Programmable Sensor Interface
Table 10. Examples of Fixed Point Signed Numbers
Decimal Value 0 1023 1024 2047 2048 3071 3072 4095 Hexadecimal Equivalent 0000h 3FFh 400h 7FFh 800h 0BFFh 0C00h 0FFFh Fixed Point Signed Number Equivalent +0.00 +0.9990234 +1.000 +1.9990234 -0.000 -0.9990234 -1.000 -1.9990234
Data Range
Various data are arranged as follows: Temperature points: 10 bits, 0-03FF in highlow order. Pressure points: 10 bits, 0-03FF in high-low order. GN1: 10 bits, 0-03FF in high-low order. OF1: 10 bits, 0-03FF in high-low order. GNTCi: signed 12 bits (with MSB for the sign), [-1.9990234, +1.9990234]. OFTCi: signed 12 bits (with MSB for the sign), [-1.9990234, +1.9990234]. Pci: signed 12 bits (with MSB for the sign), [-1.9990234, +1.9990234] DIGMO: 10 bits, 0-03FF in high-low order (See Table 13 for examples of fixed point signed numbers.)
Table 11. EEPROM Byte Definitions
Byte 0 1 2 3 4 5 6 7 8 9 10 11 Designation MODE byte Cadj Coarse Control GN1L OF1L GNTC1L OFTC1L TR1L PC5L GNTC2L P5L OFTC2L PC4L TR2L P4L GNTC3L PC3L Note Contents described in Table 9. Controls system clock during boot. Contents described in Table 12. The eight LSB's of the Fixed Gain, GN[7:0]. The eight LSB's of Fixed Offset OF[7:0]. The eight LSB's of the first gain TC GNTC1[7:0]. The eight LSB's of the first offset TC OFTC1[7:0]. The eight LSB's of the first temperature point, T1[7:0]. The eight LSB's of Pressure Coefficient 5 PC5[7:0]. The eight LSB's of the second gain TC GNTC2[7:0]. The eight LSB's of Pressure Point 5 P5[7:0]. The eight LSB's of the second offset TC OFTC2[7:0]. The eight LSB's of Pressure Coefficient 4 PC4[7:0]. The eight LSB's of the second temperature point T2[7:0]. The eight LSB's of Pressure Point 4 (or Signature) P4[7:0]. The eight LSB's of the third gain TC GNTC3[7:0]. The eight LSB's of Pressure Coefficient 3 (or Signature) PC3 [8:0].
Page 16 Apr/04
3901090308 Rev 006
MLX90308
Programmable Sensor Interface
Table 11. EEPROM Byte Definitions (continued)
Byte Designation Note
12
OFTC3L or P3L
The eight LSB's of the third offset TC OFTC3[7:0]. The eight LSB's of Pressure Point 2 (or Signature) P2[7:0]. The eight LSB's of the third temperature point T3[7:0]. The eight LSB's of Pressure Coefficient 2 PC2[7:0]. The eight LSB's of the fourth gain TC GNTC4[7:0]. The eight LSB's of Pressure Point 2 P2[7:0]. The eight LSB's of the fourth offset TC OFTC4. The eight LSB's of Pressure Coefficient 1 PC1 The eight LSB's of Pressure (output signal) Ordinate Poff[7:0]. Lower Four Bits OF1[9:8] Upper four bits. Lower four bits
13 14
TR3L or PC2L GNTC4L or P2L OFTC4L or PC1L PoffL Upper Four Bits
15
16
17
GN1[9:8]
Two MSB's of fixed gain GN[9:8]. Four MSB's of first gain TC GNTC1[11:8]. Two MSB's, first temperature point T1[9:8] or Four MSB's, Pressure Coefficient 5 PC5[11:8]. Four MSB's second offset TC OFTC2[11:8] or Four MSB's Pressure Coefficient 4 PC4[11:8]. Four MSB's third gain TC GNTC3[11:8] or Four MSB's Pressure Coefficient 3 PC3[11:8]). Two MSB's third temperature point t3[9:8] or Four MSB's Pressure Coefficient 2 PC2[11:8]. Four MSB's fourth offset TC ordinate OFTC4[11:8] or Four MSB's Pressure Coefficient 1 PC1[11:8].
Page 17 Page 17
Two MSB's of fixed offset OF[9:8] Four MSB's of the first offset TC OFTC1[11:8]. Four MSB's, second gain TC GNTC2[11:8] or TC GNTC2[11:8] or Two MSB's Pressure Point 5 P5[9:8]. Two MSB's second temperature point T2[9:8] or Two MSB's Pressure Point 4 P4[9:8]. Four MSB's third offset TC OFTC3[11:8] or Two MSB's Pressure Point 3 P3[9:8]. Four MSB's fourth gain TC GNTC4[11:8] or Two MSB's Pressure Point 2 P2[9:8]. Two MSB's Pressure Poff[9:8].
18
GNTC1[11:8]
OFTC1[11:8]
19
TR1[9:8] PC5[11:8]
GNTC2[11:8] P5[9:8]
20
OFTC2[11:8] PC4[11:8]
TR2[9:8] P4[9:8] OFTC3[11:8] P3[9:8] GNTC4[11:8] P2[9:8] Poff[9:8]
21
GNTC3[11:8] PC3[11:8]
22
TR3[9:8] PC2[9:8]
23
OFTC4[11:8]
PC1[11:8]
MLX902xx Name of Sensor Rev Y.X 22/Aug/98 3901090308
Apr/04
Rev 006
MLX90308
Programmable Sensor Interface
Table 11. EEPROM Byte Definitions (continued)
Byte 24 25 26 27 28 Designation PNB_TNB n_factor Not used ALARM low trigger Level1 IO2/IO1 ALARM low output Level2 IO2/IO1 ALARM high trigger Level3 IO2/IO1 ALARM high out level ALARM control byte Note Number of temperature and pressure gaps. See Tables 4, 5, and 6, and Figures 3 and 4. Temperature filter coefficient, four LSB's. Four MSB's must all be zero. This byte is not used. Value below which ALARM will go on. Value of first level ([IO2, IO1]= 00-01). See Figures 5 & 7. Value of DIGMO during "ALARM low" condition. Value of second level ([IO2,IO1] = 01-10). See Figures 5 and 7 Value above which ALARM will go on. Value of third level ([IO2,IO1]=10-11). See Figures 5 and 7. Value of DIGMO during "ALARM high" condition. See Figures 5 and 7. Three bits needed for choice of input for ALARM detection (TPO, IAO, GNO, VMO, IO1 or IO2). Two bits needed for choice of input for LEVEL-steering (TPO, IAO, GNO or VMO). The above bits are multiplexed according to the mode. If both CMO and VMO are active, then alarm is not active. Value of Cadj at low temperature (Don't change; factory set). Value of Cadj at mid temperature (Don't change; factory set). Value of Cadj at high temperature Don't change; factory set). First Cadj temperature point, eight MSB's of the 10 bit internal temperature value (set at factory; do not change). Second Cadj temperature point, eight MSB's of the 10 bit internal temperature value (set at factory; do not change). These bytes are not used by the firmware and are available to the user. Setting for temperature amplifier for clock temperature adjustment temperature reading (set at factory; do not change). Value sent to output if checksum test fails is a 10 bit value. These bytes are not used by the firmware and are available to the user. EEPROM checksum; value needed to make all bytes add to 0FFh. Must be set by user if checksum test is active.
Page 18 Apr/04
29 30 31
IO1/IO2 control byte
Four LSB's are unused 32 33 34 35 36 37-38 39 ClkTC1 ClkTC2 ClkTC3 Ctemp1 Ctemp2 Not used CLKgntp
40-41 42-46 47
Faultval Not Used Checksum
3901090308 Rev 006
MLX90308
Programmable Sensor Interface
Table 12. Bit Definitions; Coarse Control , Byte 2
Bit Symbol Function 7 6 5 4 3 2 1 0 IINV Invert signal sign.
Notes For Table 11
1. Not all the temperature and pressure coefficients must be used. When a coefficient is unused, the eight LSB's and the four MSB's are replaced by 0. 2. The level steering and the alarm mode cannot be active simultaneously because the levels bytes are shared with the two modes. 3. If the alarm mode and the level steering are both active, the level steering mode is dominant. The firmware will run with the level steering mode, by default. 4. If the DIGMO mode (VMO and CMO both active) is active, the alarm will be automatically disabled by the firmware. 5. At PNB_TNB address, the four MSB's correspond to the address of the last pressure point and the four LSB's to the address of the last temperature point.
GNTP1 Gain & offset of temperature amplifier. GNTP0 GNTP = 0 to 3. CSOF 1 Coarse offset of signal amplifier. CSOF 0 CSOF = 0 to 3. CSGN2 Coarse gain of signal amplifier. CSGN = 0 to 7. If CSGN > 3, CSGN1 output range = 0 to 10V. If CSGN0 CSGN <= 3, output range = 0 to 5V.
6. In the alarm_control variable, the selected input is stored on the three MSB's.
7. Pi and OFi are 10 bit values, right justified in 12 bits fields.
Table 13. RAM Byte Definitions
Byte 0 1 2 3 4 5 6 7 8 9 10 Functions MODE byte GN1L OF1L GNTC1L OFTC1L TR1L PC5L GNTC2L P5L OFTC2L PC4L TR2L P4L GNTC3L PC3L OFTC3L P3L Remarks See Table 9. Fixed gain number (8LSB). Fixed offset number (8LSB). First gain TC (8LSB). First offset TC (8LSB). First temperature point. Pressure Coefficient 5 (8LSB). Second gain TC. Pressure point 5 (8LSB). Second offset TC. Pressure coefficient 4 (8LSB). Second temperature point. Pressure Point 4 (or Signature) (8LSB). Third gain TC. Pressure Coefficient 3 (or Signature) (8LSB). Third offset TC. Pressure Point 2 (or Signature) (8LSB).
Page 19 Page 19
MLX902xx Name of Sensor Rev Y.X 22/Aug/98 3901090308
Apr/04
Rev 006
MLX90308
Programmable Sensor Interface
Table 13. RAM Byte Definitions (continued)
Byte 11 Functions TR3L PC2L GNTC4L P2L 13 OFTC4L PC1L DIGMOP1L GN1[9:8] GNTC1 [11:8] TR1[9:8] OF1[9:8] OFTC1 [11:8] GNTC2 [11:8] P5[9:8] TR2[9:8] P4[9:8] Four MSB's, Pressure Coefficient 4 PC4[11:8]. Four MSB's, Third Gain TC GNTC3[11:8] or Four MSB's, Pressure Coefficient 3 PC3[11:8]). Two MSB's, third temperature point t3[9:8] or Four MSB's, Pressure Coefficient 2 PC2[11:8]. Four MSB's Fourth Offset TC OFTC4[11:8] or Four MSB's Pressure Coefficient 1 PC1[11:8]. Same as EEPROM. Temperature filter coefficient -- 4 LSB's, 4 MSB = 0 Two MSB's, Pressure Point 4 P4[9:8]. Four MSB's Third Offset TC OFTC3[11:8] or Two MSB's Pressure Point 3 P3[9:8] Four MSB's, Fourth Gain TC GNTC4[11:8] or Two MSB's, Pressure Point 2 P2[9:8]. Two MSB's Pressure Point 1 P1[9:8]. Remarks Third temperature point. Pressure Coefficient 2 (8LSB). Fourth gain TC. Pressure Point 1 (8LSB). Fourth offset TC. Pressure Coefficient 1 (8LSB). Fixed pressure (8LSB). Two MSB's of fixed gain GN[9:8]. Four MSB's of first gain TC GNTC1[11:8]. Two MSB's, first temperature point T1[9:8] or Four MSB's Pressure Coefficient 5 PC5[11:8]. Four MSB's, second offset TC OFTC2[11:8] or Two MSB's of fixed offset OF[9:8]. Four MSB's of the first offset TC OFTC1[11:8] Four MSB's, second gain TC GNTC2[11:8] or Two MSB's, Pressure Point 5 P5[9:8] Two MSB's, second temp. point T2[9:8] or
12
14 15 16 17
PC5[11:8] 18 OFTC2[11:8] PC4[11:8]
19
GNTC3[11:8] [11:8]
OFTC3
20
PC3[11:8] TR3[9:8] [11:8]
P3[9:8] GNTC4
21
PC2[9:8] OFTC4[11:8]
P2[9:8] P1[9:8]
PC1[11:8] 22 23 24 25-26 27-28 29 PNB_TNB N_Factor Not Used GN OF Taddress
Offset Ordinate of the current gap. Gain Ordinate of the current gap. 4 bits for the max. temperature address of the current gap; 4 bits for the min. temperature address of the current gap.
Page 20 Apr/04
3901090308 Rev 006
MLX90308
Programmable Sensor Interface
Table 13. RAM Byte Definitions (continued)
Byte 30 Functions ALARM control byte IO1/IO2 control byte Remarks Three bits needed for choice of input for ALARM detection (TPO, IAO, GNO, VMO, IO1 or IO2). Two bits needed for choice of input for LEVEL-steering (TPO, IAO, GNO or VMO). These bits are multiplexed according the mode. Note: if both CMO and VMO are active, then alarm is not active. Value below which ALARM will go on. Value of first level ([IO2,IO1]=00-01). Value of DIGMO during "ALARM low" condition. Value of second level ([IO2,IO1]=01-10). Value above which ALARM will go on. Value of third level ([IO2,IO1] = 10-11). 34 35-36 37-38 39-42 43-44 45 46-47 48 49 50 51-52 53 54-55 56-57 58-59 60-61 62-63 IO1/IO2 level 3 ALARM high output level A_16 B_16 RESULT_32 Tempo1 Tempo2 Signal_In Coms_backup P3_copy Adsav1 Aaccsav Baccsav DAC_gain DAC_offset Temp_f Signal_Out Adsav2 Value of DIGMO during "ALARM high" condition. 16 bits A Register. 16 bits B Register. 32 bits result (for 16 bit multiplication). Measured temperature, internal or external, and temporary variable 1. Temporary variable 2. Digitized signal value, analog and digital mode Address saved when command is send. Port 3 setting copy. Address saved at interrupt. A-Accumulators saved at interrupt. B-Accumulators saved at interrupt. DAC gain (GN). DAC offset (OF). Filtered temperature. This is a 10 bit number that is left justified in a 16 bit field. Digitized linearity corrected signal value. Digital mode only. Address saved when call.
31
ALARM low trigger level IO1/IO2 level 1 ALARM low output level IO1/IO2 level 2
32
33
ALARM high trigger level
Note: Because of space considerations, the measured temperature can't be kept in the RAM at all times. If the measured temperature is to be available, the temperature filter variable, N_Factor, must be set to 6.
MLX902xx Name of Sensor Rev Y.X 22/Aug/98 3901090308 Page 21 Page 21
Apr/04
Rev 006
MLX90308
Programmable Sensor Interface
Prototyping
Melexis offers an MLX90308 evaluation kit which contains an evaluation circuit board, serial interface cable, and software diskette. The circuit board provides the necessary circuitry for all three applications circuits shown on the next page. Also included in the circuit board is level shifting and glue logic necessary for RS-232 communications. The board has a socket with a single MLX90308 installed, and direct access to the pins of the IC. The user can easily attach bridge sensor to the board for in-system evaluation. The serial interface cable connects the evaluation board directly to a PC's serial port for in-system calibration. The software runs in the familiar Windows platform and allows for programming and evaluation of all compensation parameters within the EEPROM.
Figure 8. MLX90308 Evaluation Kit with MLX Software
3901090308 Rev 006
Page 22
Apr/04
MLX90308
Programmable Sensor Interface
Typical 90308 Applications
Figure 9a. Absolute Voltage Mode
Supply
5K Automotive apps 100 nF
VDD COMS
100 nF
FET VDD1
VBP VMO VBN GND FLT
Output
39 nF 100 nF 10 nF 10K
Ground
Figure 9b. Ratiometric Voltage Mode
Supply
5K
VDD COMS
100 nF
VDD1
VBP VMO VBN FLT TMP GND
39 nF 10 nF 10K
Output
Ground
Figure 9c. Current Mode
Supply
5K
VDD COMS
FET VDD1
100 nF 100 nF
CMO
100 nF
VBP
75 Ohms
VBN FLT TMP GND CMN
39 nF 24 Ohms
Depends on stability of the current loop
Ground
MLX902xx Name of Sensor Rev Y.X 22/Aug/98 3901090308 Page 23 Page 23
Apr/04
Rev 006
MLX90308
Programmable Sensor Interface
Figure 10. Application Example
Figure 10a. Programmable Oil Pressure Gauge
Communications Signal Out GND V+
Programmable Oil Pressure Gauge
This application example illustrates a fundamental application of the MLX90308 and a bridge type pressure sensor element. In this application, the MLX90308 uses an external FET as a pass transistor to regulate the voltage to the sensor and the analog portion of the IC. This is known as Absolute Voltage Mode, where voltage to the sensor and analog circuit is regulated independent of the supply voltage. The MLX90308 can be operated in Ratiometric Voltage Mode, in which the output (VMO) is tied to an A/D converter sharing the same supply and ground reference. A third wiring option is Current Mode, which allows the user a 4 to 20 milliampere current range to use as a 2-wire analog sensor.
Figure 10b. Programmable Oil Pressure Gauge Electrical Connections
3901090308 Rev 006
Page 24
Apr/04
MLX90308
Programmable Sensor Interface
Figure 11. Error Compensation Figure 11a. Raw Sensor Output (measured between VPB and VBN)
170
Table 14. Glossary of Terms
A/D analog to digital conversion ADC analog to digital converter ASCII American Standard Code for Information Interchange ASIC application specific integrated circuit CM current mode CMN current mode negative (supply connection) CMO current mode output COMS communication, serial CR carriage return CSGN coarse gain CSOF coarse offset CV current / voltage mode select bit DAC digital to analog converter DACFnew filtered DAC value, new DACFold filtered DAC value, old DARDIS DAC resistor disable dB decibel DOGMO digital mode EEPROM electrically erasable programmable read only memory EOC end of conversion flag bit ESD electrostatic discharge ETMI timer interrupt enable ETPI enable temperature interrupt FET field effect transistor FG fixed gain FLT filter pin GNO gain and offset adjusted digitized signal GNOF gain, offset GNTP temperature gain / offset coarse adjustment HS hardware / software limit I/O input / output IFIX fixed current output value IINV input signal invert command bit ILIM current limit kHz kilohertz, 1000 Hz LSB least significant bit mA milliamperes, 0.001 amps MODSEL mode select ms millisecond, 0.001 second MSB most significant bit MUX multiplexer mV millivolts, 0.001 Volts nF nanofarads, 1 X 10-9 farads OFC offset control PC personal computer, IBM clone pF picofarad, 1 X 10-12 farads PLL phase locked loop POR power on reset RAM random access memory RISC reduced instruction set computer ROM read only memory RS-232 industry std. serial communications protocol RX receive SAR successive approximation register STC start A/D conversion Tdiff temperature difference Text temperature, external TMI timer Interrupt TMP temperature signal TPI temperature interrupt Tref temperature reference TSTB test mode pin TX transmit UART universal asynchronous receiver / transmitter VBN bridge, positive, input VBP bridge, negative, input VDD supply voltage VM voltage mode VMGN voltage mode gain VMO voltage mode output WCB warn / cold boot WDC watch dog counter
Voltage (in mV)
0 0%
140oC 25oC -40oC
Pressure
100%
Figure 11b. Conditioned Sensor Output
4
Voltage (VDC)
1 0%
140oC 25oC -40oC
Pressure
100%
Figures 11a and 11b above illustrate the performance of an unconditioned sensor output and a conditioned sensor output versus stimulus (pressure) and temperature. It can be seen that Figure 11a has a range of only 170 mV (maximum range with a 5V supply) and has a non-linear response over a 0-100 psi range. The sensitivity of the unconditioned output will also drift over temperature, as illustrated by the three slopes. The MLX90308 corrects these errors and amplifies the output to a more usable voltage range as shown in Figure 11b.
MLX902xx Name of Sensor Rev Y.X 22/Aug/98 3901090308
Page 25 Page 25
Apr/04
Rev 006
MLX90308
Programmable Sensor Interface
Figure 12. MLX90308 Physical Characteristics, DF Package
0.32 0.23
10.65 10.00
7.60 7.40
1.27 0.40 0.51 0.33 1.27 0o to 8o
Notes:
10.50 10.10
1. All dimensions in millimeters. 2. Body dimensions do not include mold flash or protrusion, which are not to exceed 0.15mm.
2.65 2.35
0.010 min.
3901090308 Rev 006
Page 26
Apr/04
MLX90308
Programmable Sensor Interface
Reliability Information
This Melexis device is classified and qualified regarding soldering technology, solderability and moisture sensitivity level, as defined in this specification, according to following test methods:
s IPC/JEDEC J-STD-020 Moisture/Reflow Sensitivity Classification For Nonhermetic Solid State Surface Mount Devices (classification reflow profiles according to table 5-2) s EIA/JEDEC JESD22-A113 Preconditioning of Nonhermetic Surface Mount Devices Prior to Reliability Testing (reflow profiles according to table 2) s CECC00802 Standard Method For The Specification of Surface Mounting Components (SMDs) of Assessed Quality s EIA/JEDEC JESD22-B106 Resistance to soldering temperature for through-hole mounted devices s EN60749-15 Resistance to soldering temperature for through-hole mounted devices s MIL 883 Method 2003 / EIA/JEDEC JESD22-B102 Solderability
For all soldering technologies deviating from above mentioned standard conditions (regarding peak temperature, temperature gradient, temperature profile etc) additional classification and qualification tests have to be agreed upon with Melexis. The application of Wave Soldering for SMD's is allowed only after consulting Melexis regarding assurance of adhesive strength between device and board. Based on Melexis commitment to environmental responsibility, European legislation (Directive on the Restriction of the Use of Certain Hazardous substances, RoHS) and customer requests, Melexis has installed a Roadmap to qualify their package families for lead free processes also. Various lead free generic qualifications are running, current results on request. For more information on manufacturability/solderability see quality page at our website: http://www.melexis.com/html/pdf/MLXleadfree-statement.pdf
MLX902xx Name of Sensor Rev Y.X 22/Aug/98 3901090308
Page 27 Page 27
Apr/04
Rev 006
MLX90308
Programmable Sensor Interface
Disclaimer
Devices sold by Melexis are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. Melexis makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. Melexis reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with Melexis for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by Melexis for each application. The information furnished by Melexis is believed to be correct and accurate. However, Melexis shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interrupt of business or indirect, special incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of Melexis' rendering of technical or other services. (c) 2002 Melexis NV. All rights reserved.
For the latest version of this document, go to our website at:
www.melexis.com
Or for additional information contact Melexis Direct:
Europe and Japan: All other locations:
Phone: +32 13 67 04 95 Phone: +1 603 223 2362 E-mail: sales_europe@melexis.com E-mail: sales_usa@melexis.com
ISO/TS16949 and ISO14001 Certified 3901090308 Rev 006 Page 28 Apr/04

▲Up To Search▲

Price & Availability of MLX90308LUF

	To Download MLX90308LUF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .